|
Welcome,
Guest
|
TOPIC: 1500 J/xs mock up
1500 J/xs mock up 14 years 7 months ago #6140
|
For kicks I put my 1500J wrap on my 1250 today while installing dual cable steering. Make some more runs in the morning. Steering is awesome!!!
Stability mods so far. Jack Plate, Dual Cable Steer, New Swivel Pin, Cleaver Prop, Solid Motor Mounts. All will come to gether to make me safe and happy I hope. Ill report my luck if it dont rain tomorrow. Conrad 
|
|
|
Please Log in or Create an account to join the conversation. |
Re:1500 J/xs mock up 14 years 7 months ago #6194
|
Well its video, not good video but video of it today. Not quite 62mph with more left. Each time in the video its just coming up to 60ish then I back out. It has some left in it. Just to the right of where I was videoing the wind was wrapping around and causing decent sized waves so I couldnt do a full WOT pass. Conrad |
|
|
Please Log in or Create an account to join the conversation. |
Re:1500 J/xs mock up 14 years 7 months ago #6313
|
Way to go can't wait to see it all hanging out. I see it is al coming together for ya.
|
|
|
Please Log in or Create an account to join the conversation. |
Re:1500 J/xs mock up 14 years 7 months ago #6314
|
Way to go can't wait to see it all hanging out. I see it is al coming together for ya.
|
|
|
Please Log in or Create an account to join the conversation. |
Re:1500 J/xs mock up 14 years 7 months ago #6334
|
Cool video, any close ups of the jack plate?, Mike
|
|
|
Please Log in or Create an account to join the conversation. |
Re:1500 J/xs mock up 14 years 7 months ago #6421
|
I MUST have that prop!!!
 |
|
Please Log in or Create an account to join the conversation. |
Re:1500 J/xs mock up 14 years 7 months ago #6463
|
There was one a few weeks ago on cl in yuciapa for 50 bucks.
|
|
|
Please Log in or Create an account to join the conversation. |
Re:1500 J/xs mock up 14 years 7 months ago #6470
|
Conrad your really getting the Carson dialed in this year...good job
Michael |
|
|
Please Log in or Create an account to join the conversation. |
Re:1500 J/xs mock up 14 years 7 months ago #6859
|
NEW VID
I took the carlson contender out with the 1250 today cause it was pretty calm. Had a buddy that wanted a ride so he shot some video. It ran me and him up stream at 60 mph. And just me I recorded 66.5 on one GPS and my second GPS said 68. There is some lag to GPS's some times so they will not get you at full speed if you dont hold it for a bit of a time. Id say I was knocking on the 65 mph door today. When I had my fast run it was still accelerating but this thing does not turn and I had to make the bend in the river VID Conra |
|
|
Please Log in or Create an account to join the conversation. |
Re:1500 J/xs mock up 14 years 7 months ago #6862
|
That thing moves!!
What pitch prop is that and what RPM's is it turning?? |
|
Please Log in or Create an account to join the conversation. |
Re:1500 J/xs mock up 14 years 7 months ago #6864
|
Its marked 25 pitch and its and OMC over the hub cleaver. Looks like someone hammered extra cup into it at one time. RPM unknown? Tach broke. Id love to know tho...... I bet it closing in on 6k
Conrad |
|
|
Please Log in or Create an account to join the conversation. |
Re:1500 J/xs mock up 14 years 7 months ago #6871
|
Probably at least...highest my 1350 has ever seen was 5600 and it wasnt screaming like yours!
Id love to find one of those props to try though...all mine are just standard through hub exhaust props. Its on a boat thats about 1.5-2 feet longer and probably a little bit heavier than your Carlson but im nowhere near 60(51-52 on a good day in smooth water with minimal load). I run the motor so high though, id probably really benefit from a cleaver style since they like to be at or just slightly above the waterline. Someday...  |
|
Please Log in or Create an account to join the conversation. |
Re:1500 J/xs mock up 14 years 7 months ago #6872
|
I run my motor 4.5 inches up right now. Im going to try 5-6 inches next time. Water pressure guage on the cooling system is a must at that height.
My props are 1/3 out of the water Conrad |
|
|
Please Log in or Create an account to join the conversation. |
Re:1500 J/xs mock up 14 years 7 months ago #6879
|
Keep in mind, choppers lift the bow, cleavers lift the stern. That Carlson doesn't need any bow lift, cleaver works properly. Longer and heavier, needing trim to float the bow, stick to round ear. Got a pic of the transom/lower unit height at the keel?
|
|
|
Please Log in or Create an account to join the conversation. |
Re:1500 J/xs mock up 14 years 7 months ago #6880
|
Oops.... that was for Jer.
|
|
|
Please Log in or Create an account to join the conversation. |
Re:1500 J/xs mock up 14 years 7 months ago #6881
|
The cav plate is about 2...2.5 inches above the keel. Ill get a pic of it...
Its on the boat in my avatar...1970 Challenger(nearly a flatbottom...very, very slight V profile). It requires ALOT of upward trim to get any real speed out of it... |
|
Please Log in or Create an account to join the conversation. |
Re:1500 J/xs mock up 14 years 7 months ago #6967
|
Definitely need a chopper profile. Merc sold them for the inlines in the 70's and 80's. Worth finding. Needing a lot of trim could also mean you need a setback plate (jackplate) with about 4-6 inches of setback. That will reduce the amount of trim you need to get the bow to float. Too much trim can rob speed- she should run slightly bow up with minimal uptrim, so the gearcase doesn't drag thru the water at an angle. Love the boat, by the way!!!!!!!!
|
|
|
Please Log in or Create an account to join the conversation. |
Re:1500 J/xs mock up 14 years 7 months ago #6974
|
Thanks for the info...I'll start another thread on it and maybe you can give me some more insight to goin FASTER!
Milkdud, we need more video! I keep watching that one over and over...the sound of that merc screaming at the top of it's lungs puts a smile on my face!! |
|
Please Log in or Create an account to join the conversation. |
Re:1500 J/xs mock up 14 years 7 months ago #7027
|
Here is the Switzer equivalent to the Contender. This is a 69 Shooting Star with a 76 XS and a SSM lower. Motor is high on a built up factory transom with factory tie bars. Does about 82 to 84 depending on wind ripple/direction. like yours this DOES NOT TURN either!!!
I love your video, nice hole shot! It takes quite a while for me to plane, the prop used is about 8 inches in dia, 17 pitch 1:1 ratio lower, you crank it to 5000 and let it sit there and then it will finally plane off. Bounces like hell till 50 or so and starts to fly the bow at about 65 then picks up speed quick till just over the 80 mph mark. Funny I was going to put on 1250 cowls on the XS for the correct year look you went the other way, XS cowls on a 1250! Keep the old "fast glass" alive and screamin' Randy 
|
|
|
Please Log in or Create an account to join the conversation. |
Re:1500 J/xs mock up 14 years 7 months ago #7030
|
Randy did they rate the Shooting star for 125-150 hp? My contender is only rated for 85. Not sure I want to go much faster than high 60's with this thing. I have a 1500 J block 1975(the cowls you see on the 1250) but man this thing at 70ish would be haul'n I cannot imagine 80 mph in a boat like this.
Conrad Ill get more video when I get it out next time. |
|
|
Please Log in or Create an account to join the conversation. |
Re:1500 J/xs mock up 14 years 7 months ago #7035
|
A boat will go as fast as the RIGGING will SAFELY run it. Your Contender, according to your first post, has the stuff. Hope you are also using a lanyard kill switch. About 10 years ago, a boat FLEW (!!!!!!!!!) past me, I was just able to I.D. it as a 14' Checkmate ( I used to own one) with a Merc V-6 (!!!!!!!) screaming its song. Saw it beached later, it had one center mounted seat and primo hardware/rigging. Owner said it would do mid-90 mph, but he was very careful to watch the water at speed. I can only imagine what a wave would do to something like that.
|
|
|
Please Log in or Create an account to join the conversation. |
Re:1500 J/xs mock up 14 years 7 months ago #7037
|
painfully cool boat Randy. I am sure you have it set up right.
|
|
|
Please Log in or Create an account to join the conversation. |
Re:1500 J/xs mock up 14 years 7 months ago #7047
|
Jeff you need to try a chopper id guess. Ive got a 24 and 26 pitch but they dont work as well on my boat.
look for a "small ear" or "inline" chopper. they are the same. They are smaller ear and 14 inch diameter vs the larger choppers on the V-6 motors these are the part numbers to look for Right Hand Rotation 48 75766 A4 18p 48 75768 A4 20p 48 75770 A4 22p 48 75772 A4 24p 48 75774 A4 26p 48 76108 A4 28p 48 78800 A4 30p 48 75766 A5 18p 48 75768 A5 20p 48 75770 A5 22p 48 75772 A5 24p 48 75774 A5 26p 48 76108 A5 28p 48 78800 A5 30p |
|
|
Please Log in or Create an account to join the conversation. |
Re:1500 J/xs mock up 14 years 7 months ago #7057
|
milkdud wrote:
Thanks for the info!! Whats the differences between the A4 and A5's?? I would imagine somewhere around a 22-24 would work pretty well the way its currently setup. |
|
Please Log in or Create an account to join the conversation. |
Re:1500 J/xs mock up 14 years 7 months ago #7128
|
Try the 24, if you can.
|
|
|
Please Log in or Create an account to join the conversation. |
Re:1500 J/xs mock up 14 years 7 months ago #7306
|
Randy:
I am curious how you are reading your speed? Is that with a water pickup speedo or are those GPS readings? Regards, Danny Léger 63g3 wrote:
|
|
|
Please Log in or Create an account to join the conversation. |
Donate
Please consider supporting our efforts.
Glassified Ads
1956 Lonestar Meteor |
Mercury outboard( / Engines)
Classic Mercury Outboard Motors( / Engines)
FG Login
FiberGoogle
Who's Online
We have 14946 guests and one member online