Welcome, Guest
Username: Password: Remember me
  • Page:
  • 1

TOPIC: 1973 Evinrude 85HP lube leak

1973 Evinrude 85HP lube leak 6 years 2 months ago #137845

  • ultraclyde
  • ultraclyde's Avatar Topic Author
  • Offline
  • Senior Boarder
  • Senior Boarder
  • Posts: 171
  • Karma: 3
  • Thank you received: 8
Hey all - I walked past my boat today and noticed it's leaking just a little gear lube down the skeg and dripping on the floor. It looks to be coming from the bolt that mounts the torque tab. Been about 2 weeks since it was on the water.

Whatcha think? Prop shaft oil seals?

Please Log in or Create an account to join the conversation.

1973 Evinrude 85HP lube leak 6 years 2 months ago #137846

  • ed-mc
  • Offline
  • Platinum Boarder
  • Platinum Boarder
  • Posts: 1412
  • Karma: 232
  • Thank you received: 117
Is it stinky like sulfur or just an oily, gassy smell. If it's stinky and you find water in the gearcase when you pop the drain plug, you likely have a bad seal somewhere.

The most common leakage point is from the driveshaft seals. You can access those after pulling the lower unit and water pump assembly. The oil seals are pressed-into a square block that's held on to the gearcase housing with (4) bolts. If this is a fresh-water-run motor, the bolts will probably come right out. If they don't, or you have a Salty-Dog, the only way you'll get 'em out without breaking is with application of heat. A MAPP torch is best, it'll put out plenty of heat with no danger or melting parts. But you could do it with a propane torch if it has a good flame.

Here's a parts breakdown to give you an ideal of what you'll need for this job (usually just the seals and an O-ring for the driveshaft bearing/seal carrier):

www.marineengine.com/parts/johnson-evinrude-parts.php?year=1973&hp=85&model=85ESL73M&manufacturer=Johnson§ion=Gearcase

Part numbers 3, 4, and 5 on the diagram. Note there are (2) seals, one with lips down and one with lips up.

If the leaking isn't obvious, you may have to pressure-test the L/U to approx 12 psi to find a leak.

Upon reassembly, put a light coating of Permatex #3 around the bearing carrier O-ring and also on the bolt threads. Guaranteed they'll never seize.

All that being said, it's not uncommon to see an oily discharge run out of the nether regions. If it's not stinky, but only oily-gassy smelling, it's probably just "mung" from the exhaust. And especially if your gear oil shows no sign of water. Because, invariably, if oil escapes the gearcase, it will be displaced by water.

HTH & let us know what you find.........ed

Please Log in or Create an account to join the conversation.

1973 Evinrude 85HP lube leak 6 years 2 months ago #137849

  • ultraclyde
  • ultraclyde's Avatar Topic Author
  • Offline
  • Senior Boarder
  • Senior Boarder
  • Posts: 171
  • Karma: 3
  • Thank you received: 8
I didn't smell it, but it didn't look milky. In fact, now that you mention it, it looked sooty like maybe exhaust mixed with water. The last day on the lake was a company event where i was giving boat rides, so I ran it all day with the boat loaded heavy. I'd bet I've just got some out-of-the-ordinary exhaust buildup with some oily blow-by.

I'll check it and get back with you. It's about time to do the impeller this winter anyway, so it would be a good time to do the seals too if it IS a problem.

Please Log in or Create an account to join the conversation.

1973 Evinrude 85HP lube leak 6 years 2 months ago #137852

  • ed-mc
  • Offline
  • Platinum Boarder
  • Platinum Boarder
  • Posts: 1412
  • Karma: 232
  • Thank you received: 117
Maybe a good idea to throw some Seafoam or Gumout Regane carbon-cleaning additive in the fuel. Regane is cheep at Walmart and highly effective, with a high load of PEA (polyetheramine) which cleans carbon deposits like crazy.

Sure sounds like combustion products to me. Cheers.......ed

Please Log in or Create an account to join the conversation.

1973 Evinrude 85HP lube leak 6 years 2 months ago #137857

  • ultraclyde
  • ultraclyde's Avatar Topic Author
  • Offline
  • Senior Boarder
  • Senior Boarder
  • Posts: 171
  • Karma: 3
  • Thank you received: 8
I did a quick check when I got home. The drip streaks on the skeg have no smell. Pulled the fill plug and the lube looks fine, slight sulfur smell like normal. I'm guessing it's just exhaust dribble.

Good thought on adding a little something to the next tank.

Please Log in or Create an account to join the conversation.

  • Page:
  • 1
Time to create page: 0.208 seconds

Donate

Please consider supporting our efforts.

Glassified Ads

1956 Lonestar Meteor
( / Boats)

1956 Lonestar Meteor
12-24-2024

Mercury outboard
( / Engines)

noimage
11-03-2024

Classic Mercury Outboard Motors
( / Engines)

Classic Mercury Outboard Motors
10-18-2024

FG Login

FiberGoogle

Who's Online

We have 13390 guests and one member online