Welcome, Guest
Username: Password: Remember me
  • Page:
  • 1

TOPIC: 1983 evinrude 115 compression test

1983 evinrude 115 compression test 7 years 4 months ago #133242

So I did a compression test on my motor tonight and two cylinders are at 100 psi and two are at 60 psi. Has anyone had any success with ring free working to increase cylinder pressure? I would hate to pull the boat off the water for the rest of the year. Come October it will be out of the water and i can tear into it then if need be. A second question is what would ibe looking at on average for a rebuild on it?

Please Log in or Create an account to join the conversation.

1983 evinrude 115 compression test 7 years 4 months ago #133274

On those V-4 engines you can pull a bypass cover easier & cheaper than you can pull a cylinder head. You can see a problem better too. Better way to check for stuck rings. Six 3/8" headed bolts hold them on. They are on the port & starboard sides of the block. I would start with the starboard side. You didn't say which cylinders were low, but usually it is the starboard cylinders #1 & #3 that will stick the rings the worst. After you get the cover off you can see the side of the piston & rings. A small screwdriver can be used to push on the rings to see if they will move in and out in the piston grooves. If they are all gummed up they are stuck. You can buy BRP/Mercury Engine Tuner or Power Tune which can clean this up. Ring Free will keep the engine clean, but will take awhile to get it all out. Put the tuner in the ports before putting the bypass covers back on. Also put it on top of the Pistons thru the spark plug holes. Leave it in for 24 hrs, but not much longer. You need to start the engine after that and run it a minimum of 15 minutes to get it out of the system. It is corrosive. You can do the process again with a warm engine which is even better. Just remember you have to run the motor after it sits!
This is all predicated on you not finding any piston damage when you open the bypass covers. If you do have to rebuild replace all 4 pistons. These motors (as all 2 strokes) have a history of dropping dow pins (hold the rings in place). When that happens the rings rotate & get clipped by the port openings. Good luck with you decarboning.

Dan in TN
The following user(s) said Thank You: VinTin, Jollyrog68

Please Log in or Create an account to join the conversation.

1983 evinrude 115 compression test 7 years 4 months ago #133277

  • ed-mc
  • Offline
  • Platinum Boarder
  • Platinum Boarder
  • Posts: 1412
  • Karma: 232
  • Thank you received: 117
In addition to what the O.P. said, if the 2 low cylinders are on the same side, you may have a blown head gasket. A leaky gasket between 2 cylinders can cause low readings in each; it's just suspicious that 2 cyliinders have the same low reading.

Please Log in or Create an account to join the conversation.

1983 evinrude 115 compression test 7 years 4 months ago #133283

They are on opposite sides unfortunately.

Please Log in or Create an account to join the conversation.

1983 evinrude 115 compression test 7 years 4 months ago #133288

I did forget the head gasket which would be a good call, but now that we know opposite sides it looks more like scored cylinders? Maybe lean carburetor or such. Still looking through the bypass covers is better for first clance. You should see the scores on the piston. Then you can pull the head. Either way the engine will have to be pulled apart. Hope that helps.

Dan in TN

Please Log in or Create an account to join the conversation.

1983 evinrude 115 compression test 7 years 4 months ago #133290

Thank you t2stroke i will look at them tonight when i get home from work and hope its a ring issue. I will let you know what i find.

Please Log in or Create an account to join the conversation.

1983 evinrude 115 compression test 7 years 3 months ago #133784

Any updates? I'm curious how this process will go. I've got an 85HP V4 that may need help one day...

Please Log in or Create an account to join the conversation.

  • Page:
  • 1
Time to create page: 0.174 seconds

Donate

Please consider supporting our efforts.

Glassified Ads

1956 Lonestar Meteor
( / Boats)

1956 Lonestar Meteor
12-24-2024

Mercury outboard
( / Engines)

noimage
11-03-2024

Classic Mercury Outboard Motors
( / Engines)

Classic Mercury Outboard Motors
10-18-2024

FG Login

FiberGoogle

Who's Online

We have 11790 guests and no members online