|
Welcome,
Guest
|
|
TOPIC: Plugs for my 115 ?
Re:Plugs for my 115 ? 14 years 9 months ago #2462
|
Don, I won't install anything but NGK plugs in anything I own. I've worked in the parts business a long time, and tried several brands in the past. (Used to get samples for free when I was in purchasing!) I've never had an NGK plug fail plus the threads are rolled, not cut. This means less wear and tear on the threads in the engine, believe it or not.
I also recommend using a light dab of anti-seize compound on the threads before installing, just as a preventive measure. A minute to check the gap, and proper torque are also a very good idea. Just my two cents. Have you fired her up yet? I saw your earlier post, looks good. |
|
|
Please Log in or Create an account to join the conversation.
Mark
|
Re:Plugs for my 115 ? 14 years 9 months ago #2465
|
Don,
The OEM plug is NGK-BUHW 
|
|
Please Log in or Create an account to join the conversation. |
Re:Plugs for my 115 ? 14 years 9 months ago #2467
|
Thanks.........Might try this weekend if my Merc guy is available. Good to have an experienced onlooker giving me instructions and checking everything out. I will need to remove the control cables to run them through the splashwell when installing it on the GT. I assume it is the throttle control box that the cables need to come out of to do this not the engine ones ?
|
|
Please Log in or Create an account to join the conversation. |
Re:Plugs for my 115 ? 14 years 9 months ago #2468
|
Fuel, throttle, ignition typically all come through that splashwell hole unless you have another one on the other side to share.
Disconnections at the motor end. |
|
Please Log in or Create an account to join the conversation. |
Re:Plugs for my 115 ? 14 years 9 months ago #2528
|
Thanks for that info.........First time Merc guy so have to ask a bunch of questions....I don't like surprises !
What is the proper torque on the plugs ? Guess it is in my Seloc manual........ |
|
Please Log in or Create an account to join the conversation. |
Re:Plugs for my 115 ? 14 years 9 months ago #2537
|
Don
Where did you come across the nifty trim fitting for the steering cable? lar |
|
|
Please Log in or Create an account to join the conversation. |
Re:Plugs for my 115 ? 14 years 9 months ago #2541
|
That is actually a type of tube mount. It comes with the tube and bezel as a kit. You can buy them from places like west marine, overtons, etc.
http://www.westmarine.com/webapp/wcs/stores/servlet/producte/10001/-1/10001/17500/377%20710%201727/7 |
|
Please Log in or Create an account to join the conversation.
Some people are like slinkies... Not much good for anything, but they sure are fun to push down the stairs.
|
Re:Plugs for my 115 ? 14 years 9 months ago #2597
|
Torque on those plugs should be 20 ft lbs, or 1/4 turn past the gasket contacting the head.
|
|
|
Please Log in or Create an account to join the conversation.
Mark
|
Re:Plugs for my 115 ? 14 years 9 months ago #2615
|
boatgeek wrote:
That is the original stainless steel splaswell cable mount that was on the boat when I got it. I have not heard or have I seen another one like it. Somebody must have one. I used the old steeing tube and conected it to the new Teleflex steeering cable assy. The new tube would not fit the old mount.......So now it is back to original! The original hole cut out on the splashwell is smaller also than the new mounts require. I used all new mounts and cable on my '78 Manatee restoration 
|
|
Please Log in or Create an account to join the conversation. |
Re:Plugs for my 115 ? 14 years 9 months ago #2616
|
Looking good on both boats, Don! You do nice work. I was stationed at Langley AFB for a while back in the day, remember going to Virginia Beach on the weekends. ("I was gone for a minute, but I'm back now."
 ) |
|
|
Please Log in or Create an account to join the conversation.
Mark
|
Re:Plugs for my 115 ? 14 years 9 months ago #2621
|
MarkS wrote:
I did a 1971 Beuhler Bolero - Thought you might like to take a look......... 
|
|
Please Log in or Create an account to join the conversation. |
Re:Plugs for my 115 ? 14 years 9 months ago #2627
|
WOW factor 10! Now that is gorgeous, thanks.
 |
|
|
Please Log in or Create an account to join the conversation.
Mark
|
Re:Plugs for my 115 ? 14 years 9 months ago #2638
|
MarkS wrote:
Yep, I agree.........Sold it a couple years back..... 
|
|
Please Log in or Create an account to join the conversation. |
Re:Plugs for my 115 ? 14 years 9 months ago #2643
|
I've become a big fan of NGK's irridium plugs lately. Believe mine are #BR7HIX. Love em. Smoother low speed, less 'sputtering', possible relationship 'tween plugs & new best top speed, etc.
Nine bucks a pop at NAPA but I figure we're worth it ... 
|
|
|
Please Log in or Create an account to join the conversation. |
Re:Plugs for my 115 ? 14 years 9 months ago #2652
|
Ordered the plugs - Will get them today..........Maybe get it started this week !
|
|
Please Log in or Create an account to join the conversation. |
Re:Plugs for my 115 ? 14 years 9 months ago #2724
|
Glastron_GT160 wrote:
Got 'em.......... 
|
|
Please Log in or Create an account to join the conversation. |
Re:Plugs for my 115 ? 14 years 9 months ago #2725
|
Top five plugs are easy to change. Bottom one, the lower cowling is in the way. I always use an adjustable wrench to break it loose. I remove and instal it by hand, then use the adjustable at the end to snug it up.
Good luck. |
|
Please Log in or Create an account to join the conversation. |
Re:Plugs for my 115 ? 14 years 9 months ago #2759
|
ngk.com
buhw $2.89 each plus shipping. |
|
|
Please Log in or Create an account to join the conversation. |
Re:Plugs for my 115 ? 14 years 9 months ago #2806
|
g3jim wrote:
Thanks for the info........Advance Auto Parts here in VA cost me 3.14 ea. including tax. Priced NGK.com. With UPS shipping would have been 4.57 ea. Anyway, when I had the motor comp tested the guy, as I recall, did not ground the loose plug wires and since I am not a Merc mechanic I was wondering if that would cause any electrical problems ? I seem to remember reading that the plug wires were to be grounded to the block during the test. I want to put the gas to it this weekend. Don 
|
|
Please Log in or Create an account to join the conversation. |
Re:Plugs for my 115 ? 14 years 9 months ago #2807
|
Don, hopefully he was spinning the motor over without energizing the ignition system. I sought advise here on this subject before doing the compression check on my 73 Johnson 115, and learned that it can be done that way with no damage. Can you test run (with cooling water supply) at home before heading to the lake?
PS- Good $ deal at advance, that's why they're my first choice when buying car parts, never thought of getting my boat stuff down there. (One duh for Mark) Thanks! |
|
|
Please Log in or Create an account to join the conversation.
Mark
|
Re:Plugs for my 115 ? 14 years 9 months ago #2809
|
Used the start key on the throttle control box to turn it over. They were supposed to know what they were doing....So, do you think I have a possible problem ?
|
|
Please Log in or Create an account to join the conversation. |
Re:Plugs for my 115 ? 14 years 9 months ago #2811
|
Not sure on your motor how the ign. system would be disabled. Sometimes a simple ground wire hooked to the right terminal can suffice, I'm still a rookie at this compared to most here. Did they hook up any jumper wires, or disconnect any wires on the motor before running the test? I would definitely get a set of "ear muffs" to run water to the motor and test it in the driveway before proceeding to the lake/river/whatever.
|
|
|
Please Log in or Create an account to join the conversation.
Mark
|
Re:Plugs for my 115 ? 14 years 9 months ago #2812
|
Thanks,
As I recall he did connect a jumper to the block on each cyl he was testing to see about good spark on the plug wire. One at a time as he was going from 1-2-3 etc. The pressure guage was in and the plug wire was grounded on each as he went down......At least one plug wire was grounded each time as we turned it over.... Does that make sense? |
|
Please Log in or Create an account to join the conversation. |
Re:Plugs for my 115 ? 14 years 9 months ago #2813
|
It's not the way I would go about it, but it may be okay. Like I said earlier, I'm no expert on this, still learning. I think you'll probably be alright, sincerely hope so. What kind of shop / mechanic was this?
You can pick up a set of ear muffs (flushing - test device that you connect a garden hose to) for under $10 at Wal-Mart or somewhere similar! Gotta get ready for work, good luck Don. |
|
|
Please Log in or Create an account to join the conversation.
Mark
|
Re:Plugs for my 115 ? 14 years 9 months ago #2814
|
I have an identical motor that I have just set the timing on as per the Merc manual & that involves removing all the plugs apart from no 1 & it doesn't say anything about grounding the remaining leads/plugs & I didn't do so. It runs fine still!!
 Geoff UK |
|
|
Please Log in or Create an account to join the conversation. |
Re:Plugs for my 115 ? 14 years 9 months ago #2815
|
"I feel so much better now that I have given up all hope" Just kidding...............I should be ok...Will put it to the test soon !
|
|
Please Log in or Create an account to join the conversation. |
Re:Plugs for my 115 ? 14 years 9 months ago #2816
|
Fins
Thanks for the info and link lar |
|
|
Please Log in or Create an account to join the conversation. |
Re:Plugs for my 115 ? 14 years 9 months ago #2820
|
Don,
On any of these solid state high output ignition systems like your adi system or a solid state distributor (trigger) system should definitely have the spark controlled with doing troubleshooting, compressions, etc. Otherwise the ignition tries to throw a spark and if it can't reach ground it seeks the closest alternative and consequently you can end up with damaged switchboxes, etc. If all (6) are still firing it is probably still just fine. The adi system does NOT need 12v to activate it - it is self generating so beware that if the control harness is not connected to the engine or the key is 'ON' she might just start anyway if sparkplug wires are connected and the flywheel gets turned a bit. Simply put,...Your Merc will start on a motor stand with no control harness attached if you simply turned the flywheel or prop. I built a tool to control the arc of the plug wires while testing, etc. It is a piece of flat-bar with (6) old sparkplugs welded to it. I spread the gap so the spark could be easily seen. I ground the flat-bar to the engine block. If you don't need spark while testing something the safe thing to do is to simply attach a jumper wire to the orange or black with yellow strip kill circuit terminal on the switchboxes and to engine ground. (some are orange - some are black with a yellow stripe. Whatever color wire that is going to the Mercury Safety switch is the circuit. Thom |
|
Please Log in or Create an account to join the conversation. |
Re:Plugs for my 115 ? 14 years 9 months ago #2824
|
Don , one small thing with these i6's before you start changing plugs, stuff a rag down under #6 just in case you drop a plug , their a real pain in the a@# to get out if they fall in there . been there lol . Gil
|
|
Please Log in or Create an account to join the conversation. |
Re:Plugs for my 115 ? 14 years 9 months ago #2870
|
boatgeek wrote:
If you are looking for this ....... norfolk.craigslist.org/boa/1631150719.html I have one I need to get rid of.....Don |
|
Please Log in or Create an account to join the conversation. |
Re:Plugs for my 115 ? 14 years 9 months ago #2876
|
Thom said "On any of these solid state high output ignition systems like your adi system or a solid state distributor (trigger) system should definitely have the spark controlled with doing troubleshooting, compressions, etc."
So I should have been controlling the spark when I timed my '84 115 then Thom? The Merc book just says to pull the leads off & remove the plugs, I will bear that in mind next time. Geoff UK |
|
|
Please Log in or Create an account to join the conversation. |
Plugs for my my '63 1000 14 years 9 months ago #2903
|
I checked NGK's web site and came up with B7S. Unfortunately, they do not make it in iridium. They do for a 5 (colder) but not the 7. I don't think I'd want to run a colder plug would I? Anyways, I'm getting a set of the B7S for now.
This has been a great thread folks, thanks! Frank |
|
Please Log in or Create an account to join the conversation. |
Re:Plugs for my 115 ? 14 years 9 months ago #2945
|
Frank, I wouldn't change the heat range on the plugs just to go to iridium! The colder plugs will foul quicker, and could have a negative effect on performance as well. Just my two cents.
 |
|
|
Please Log in or Create an account to join the conversation.
Mark
|
Re:Plugs for my 115 ? 14 years 9 months ago #2950
|
That is eggsackly how I feel Mark!
Frank |
|
Please Log in or Create an account to join the conversation. |
Re:Plugs for my 115 ? 14 years 9 months ago #2953
|
I do not believe that the 86 - 115 HP has a thermostat. So in certain areas where the water is " cold " the motor will run / idle with a cool block.
A " cold " spark plug will get rid of heat quicker ( relative to a hotter plug )as there is a shorter path to the block. Top end performance is likely the same between a hot or colder plug. |
|
|
Please Log in or Create an account to join the conversation. |
Re:Plugs for my 115 ? 14 years 9 months ago #2974
|
Alacrity wrote:
I am sure my Merc is an '85........... Tried to post pics of the tag not so good but looks like 1985..... 
|
|
Please Log in or Create an account to join the conversation. |
Re:Plugs for my 115 ? 14 years 9 months ago #2981
|
Definitely a 1985 motor, as we've already discused, here:
Re: Just brought home a 1974 GT-160
Doesn't matter though as I believe none of those late model inline 6's had a thermostat. I'd be nervous running any other plug other than something Mercury recommended. These motors are susceptible to detontation and pre-ignition and over the years have had to be timed less-advanced to be reliable (especially on modern fuel). A hotter plug will increase this risk of pre-ignition, equivalent to advancing the timing. A risk I personally wouldn't choose to take. p.s. Don, I found the GT emblem, and will get it out to you asap. 
|
|
Please Log in or Create an account to join the conversation. |
Re:Plugs for my 115 ? 14 years 9 months ago #3000
|
I love it! Good advise, Chris.
|
|
|
Please Log in or Create an account to join the conversation.
Mark
|
Re:Plugs for my 115 ? 14 years 9 months ago #3013
|
Don_Gt-160 wrote:
Don Not exactly looking for one of those. Just thought it was a nice touch on the splashwell. lar |
|
|
Please Log in or Create an account to join the conversation. |
|
Moderators: kensikora, classicfins, bruce gerard, billr, mrusson, cc1000, MarkS, Waterwings, jbcurt00
Time to create page: 0.324 seconds
Donate
Please consider supporting our efforts.
Glassified Ads
1956 Lonestar Meteor |
Mercury outboard( / Engines)
11-03-2024
Classic Mercury Outboard Motors( / Engines)
10-18-2024
FG Login
FiberGoogle
Who's Online
We have 14837 guests and one member online